While the defaults for Encryption are set at 4500-4500 and these settings are preferred, there may be instances where (depending on what the Home router supports) the user may need to either disable this setting, or change to one of the other options.ĥ. Review the Sample 46vpnsetting.txt file for simplifying configuration settings on the IP Phones.Ĥ. Failure to do so will result in No Speech path when two VPN extensions try and establish a call.ģ. It will be necessary to uncheck the Direct Media Path checkbox in the Extension Configuration in IP Office. IMPORTANT: Many VPN Routers will not allow a direct media path to be established between two VPN Endpoints. Typically a Home Router uses 192.168.0.x or 192.168.1.x as its internal network range therefore it is recommended that this is not used as a Virtual IP Address Range.Ģ. For instance, many VPN IP Phones may be installed at user's homes. Consider where the phone is most likely to be used and ensure that the Virtual IP Range selected will not conflict. Please take care in choosing a Virtual IP Range. ![]() The IP Phones may require a Virtual IP Address to be configured in the VPN settings. Remote ID used for Enhanced Mode test GroupVPNġ. Remote ID used for Standard Mode test GroupVPN I had the same problem and it was because I have my IPO on a different subnet. ![]() RE: Can't get past Building IPSec Tunnel iposcn (IS/IT-Management) 10 Jul 08 06:52 Is this because ESP is a standard so i do not need to change it on the phone.Īny help would be greatly appreciated. Well, in the VPN phone i do not have a setting for IPSec protocol. Now something i noticed is in the sonicwall configuration under the IPSec Proposal setup there is a protocol that is set to ESP that can NOT be changed. Virtual IP:192.168.21.54(local ip address of the phone) IKE Config Mode:Disabled(tried enabled as well) Group PSK: xxxxxxxxxxxxxxxx(PSK setup in sonicwall)Įncapsulation:RFC(have tried all other options as well) Username:vpnphone(user setup in the sonicwall) Server:79.43.xxx.xxx(public ip address of the sonicwall) I am using the Juniper w/ Xauth profile on the VPN phone with the following settings. I cant find anything on these error codes, so what are those error codes good/used for?(thats besides the point) Ip nat inside source static udp 192.168.50.2 5060 interface Dialer0 5060Īccess-list 1 permit 192.168.0.0 0.0.0.255Īccess-list 1 permit 192.168.50.0 0.0.0.I am able to exchange keys and pass Phase 1, the phone times out on Phase 2. Ip nat inside source list 1 interface Dialer0 overload ![]() Ip http timeout-policy idle 60 life 86400 requests 10000 Tunnel protection ipsec profile CiscoCP_Profile1ĭescription $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$ Isakmp authorization list ciscocp_vpn_group_ml_1Ĭrypto ipsec security-association lifetime seconds 86400Ĭrypto ipsec transform-set myset esp-3des esp-md5-hmacĬrypto ipsec transform-set myset2 esp-aes esp-sha-hmacĬrypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmacĬrypto map clientmap client authentication list userauthenĬrypto map clientmap isakmp authorization list groupauthorĬrypto map clientmap client configuration address respondĬrypto map clientmap 20 ipsec-isakmp dynamic dynmap2 Username Arsenal privilege 15 secret 5 $1$RLix$8FgYa6HelI8AeKA7sbvVr1Ĭrypto isakmp client configuration address-pool local ippoolĬrypto isakmp client configuration group groupauthorĬrypto isakmp profile ciscocp-ike-profile-1Ĭlient authentication list ciscocp_vpn_xauth_ml_1 Subject-name cn=IOS-Self-Signed-Certificate-3405674095Ĭrypto pki certificate chain TP-self-signed-3405674095Ĭertificate self-signed 01 nvram:IOS-Self-Sig#350A.cer I cant see it for the life of me.Īaa authentication login groupauthor localĪaa authentication login userauthen localĪaa authentication login ciscocp_vpn_xauth_ml_1 localĪaa authorization network groupauthor localĪaa authorization network ciscocp_vpn_group_ml_1 local Is there a routing issue with this config. I get a connection on the VPN and the phone sits there with Discover 192.168.50.2 which is the internal address of the IP office.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |